Akiles ProLam 230 Manuel d'utilisateur Page 2

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 1
TIPS:
ALWAYS TURN “OFF” THE PRO-LAM IF YOU WILL STOP LAMINATING FOR A LONG PERIOD OF TIME.
ALWAYS MAINTAIN THE PRO-LAM ON STAND BY (POWER “ON” POSITION) IF YOU WILL CONTINUE
LAMINATING WITHIN A FEW MINUTES. THIS FEATURE WILL ALLOW YOU TO INSTANTLY RE-START
LAMINATING, WITHOUT DEPRECIATING THE MOTOR OR ROLLERS.
TEMPERATURE ADJUSTMENTS:
IF THE POUCH IS NOT SEALING WELL (IT APPEARS MILKY), THE TEMPERATURE MAY BE TOO COLD FOR
THE POUCH THICKNESS THAT YOU WISH TO LAMINATE.
CORRECTIVE ACTION:
· A. MAKE SURE THAT THE TEMPERATURE IS PROPERLY SET FOR THE POUCH THICKNESS TO BE
LAMINATED.
· B. MAKE SURE THAT THE READY LIGHT IS ON.
· C. IF THE TEMPERATURE IS AT THE CORRECT POSITION AND THE READY LIGHT IS NOT ON, SIMPLY
WAIT UNTIL THE READY LIGHT TURNS ON AND PROCEED TO LAMINATE.
· D. IF BOTH THE TEMPERATURE IS AT THE CORRECT POSITION AND THE READY LIGHT IS ON, RAISE THE
TEMPERATURE POSTION ONE KNOB (CLOCK-WISE) AND WAIT APPROXIMATELY 1-2 MINUTES UNTIL
THE READY LIGHT TURNS ON AND THEN PROCEED TO LAMINATE.
E. REPEAT STEP “D” AS NEEDED. NOTE: THERE ARE MANY DIFFERENT POUCHES IN THE MARKET, THAT
MAY REQUIRE MORE OR LESS HEAT TO PROPERLY SEAL.
·IF THE POUCH IS WAVY THE TEMPERATURE IS TOO HIGH FOR THE POUCH THICKNESS THAT YOU WISH
TO LAMINATE
CORRECTIVE ACTION:
F. PROCEED WITH STEPS A, B, C, D AND E ABOVE. NOTE: TEMPERATURE CONTROL MUST BE TURNED
COUNTER-CLOCK-WISE TO LOWER TEMPERATURE.
CAUTION !
· DO NOT LEAVE THE PRO-LAM ON FOR LONG PERIODS OF TIME, WHEN NOT IN USE.
· TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPERATE THE PRO-LAM NEAR WATER.
· DO NOT USE THE PRO-LAM IF POWER CORD IS DAMAGED.
· DO NOT ALLOW THE ELECTRIC CORD TO BE IN CONTACT WITH HOT SURFACES.
· IN CASE OF MALFUNCTION, RETURN THE UNIT TO YOUR DISTRIBUTOR FOR SERVEE. THIS LAMINATOR
DOES NOT CONTAIN ANY PART THAT CAN BE SERVICED BY THE CONSUMER.
WARRANTY POLICY:
YOUR PRO-LAM HAS A WARRANTY OF ONE YEAR, FROM ITS PURCHASE DATE. IN THE EVENT OF A
MANUFACTURER’S DEFECT, YOUR DISTRIBUTOR (AT OPTION) WILL REPAIR OR REPLACE IT.
IMPORTANT: THIS WARRANTY DOES NOT COVER DAMAGES DUTO IMPROPER USE OR MISTREATMENT OF
THE UNIT, INCLUDING ANY EXTRAORDINARY EVENT LEADING TO THE DAMAGE OF THE MACHINE, WHETHER
IT IS REVERSIBLE OR NOT.
IF THE PRO-LAM IS NOT LAMINATING PROPERLY FIRST FOLLOW THE CORRECTIVE ACTIONS ABOVE. IF THE
PROBLEM PERSISTS PLEASE CONTACT YOUR DEALER FOR FURTHER INSTRUCTIONS. PLEASE HAVE YOUR
MACHINE’S SERIAL NUMBER AND THE PURCHASE DATE READY. IF THE MACHINE MUST BE RETURNED TO
YOUR DISTRIBUTOR IT IS YOUR RESPONSIBILITY TO PROPERLY PACK AND SHIP IT, AS ANY DAMAGE
INCURRED DURING ITS TRANSPORTATION IS NOT COVERED BY OUR WARRANTY POLICY.
Vue de la page 1
1 2

Commentaires sur ces manuels

Pas de commentaire